|
焊盘清理
使用Metcal的扁铲形烙铁头和吸锡编织带可以清理两面和四面引脚芯片的焊盘，方便、快捷并且非常安全。在清理焊盘时请特别注意，不要用烙铁头和吸锡带在焊盘来回拖动，这样会造成焊盘脱落。
|
扁铲形烙铁头 |
|
SMTC-X110**
扁铲形
Dual Heater Quad
1.55" |
SMTC-X62
扁铲形
0.870" (22.10mm)
长 |
SMTC-X61
扁铲形
0.620" (15.75mm)
长 |
SMTC-X60
扁铲形
0.410" (10.41mm)
长 |
**=不提供 500、800系列
用于托焊的蹄形和刀形烙铁头
|
|
 |
|
SMTC-X147*
蹄形 |
SMTC-X167**
小蹄形 |
|
 |
|
|
SMTC-X169*
长蹄形 |
SMTC-X170*
长蹄形 |
|
 |
 |
|
SMTC-X161*
刀形
(粘锡面积, .08" 2.03mm) |
SMTC-X173
刀形
(粘锡面积,.23" 5.84mm) |
*=不提供800系列 **=不提供 500、800系列
其他的电烙铁头
SLOT TIP CARTRIDGES
DIMENSIONS IN INCHES (mm) |
 |
| SMT TYPE |
A |
B |
D |
Part No. |
| Chip 0805 |
.090 (2.29) |
.050 (1.27) |
.070 (1.79 |
SMTC-X01 |
| Chip 1206, 1210 |
.140 (3.56) |
.060 (1.52) |
.070 (1.79) |
SMTC-X02 |
| Chip 1808, 1812 |
.190 (4.83) |
.080 (2.03) |
.075 (1.91) |
SMTC-X03 |
| Chip, Box A (EIA SOPM-3224) |
.135 (3.43) |
.080 (2.03) |
.120 (3.05) |
SMTC-X35 |
| Chip, Box B (EIA SOPM-3528) |
.150 (3.81) |
.095 (2.41) |
.100 (2.54) |
SMTC-X32 |
| Melf, Box B (EIA SOPM-4532) |
.190 (4.83) |
.110 (2.79) |
.160 (4.06) |
SMTC-X36 |
| Chip, Box C (EIA SOPM-6032) |
.250 (6.35) |
.095 (2.41) |
.130 (3.30) |
SMTC-X33* |
| Chip, Box D (EIA SOPM-7246) |
.300 (7.62) |
.100 (2.54) |
.140 (3.56) |
SMTCX34* |
| SOT-23 |
.068 (1.73) |
.100 (2.54) |
.050 (1.27) |
SMTC-X05 |
| SOT-89 |
.110 (2.80) |
.250 (6.35) |
.080 (2.03) |
SMTC-X08 |
| Chip 0402, 0603, 0805 (angled) |
.080 (2.03) |
.050 (1.27) |
.060 (1.52) |
SMTC-X88 |
| Chip 0402, 0603 |
.070 (1.78) |
.040 (1.02) |
.040 (1.02) |
SMTC-X96 |
500 series x=5 600 series x=0 700 series x=1 *=NOT available for 500 series
TUNNEL TIP CARTRIDGES FOR DUAL IN-LINE PACKAGES
DIMENSIONS IN INCHES (mm) |
 |
| SMT TYPE |
A2 |
A |
B |
D |
Part No. |
| DPAC |
.335 (8.51) |
.335 (8.51) |
.250 (6.35) |
.200 (5.08) |
SMTC-X47 |
| SO-8 |
.320 (8.13) |
.380 (9.65) |
.750 (19.05) |
.240 (6.10) |
SMTC-X107 |
| SO-16 |
.330 (8.38) |
.330 (8.38) |
.475 (12.07) |
.230 (5.84) |
SMTC-X46* |
| SO-8 |
.335 (8.51) |
.335 (8.51) |
.665 (16.90) |
.250 (6.35) |
SMTC-X68** |
| SOIC-8 |
.200 (5.08) |
.200 (5.08) |
.170 (4.32) |
.090 (2.29) |
SMTC-X04 |
| SOIC-14,-16 |
.200 (5.08) |
.200 (5.08) |
.400 (10.16) |
.090 (2.29) |
SMTC-X06 |
| SOIC-14 |
.204 (5.18) |
.204 (5.18) |
.350 (8.89) |
.100 (2.54) |
SMTC-X142 |
| SOIC-24 (Mini flat pack) |
.280 (7.11) |
.280 (7.11) |
.620 (15.75) |
.125 (3.18) |
SMTC-X77 |
| SOIC-16 (Wide) |
.320 (8.13) |
.320 (8.13) |
.470 (11.94) |
.270 (6.86) |
SMTC-X124 |
| SOIC-20 |
.375 (9.53) |
.375 (9.53) |
.520 (13.21) |
.125 (3.18) |
SMTC-X10 |
| SOIC-24 |
.375 (9.53) |
.375 (9.53) |
.620 (15.75) |
.125 (3.18) |
SMTC-X09 |
| SOIC-28, SOL-34 |
.375 (9.53) |
.375 (9.53) |
.720 (18.29) |
.125 (3.18) |
SMTC-X07 |
| SOIC-32 |
.520 (13.21) |
.520 (13.21) |
.805 (20.45) |
.170 (4.32) |
SMTC-X42 |
| SOJ-28, SOM-36 |
.315 (8.00) |
.340 (8.64) |
.740 (18.80) |
.074 (1.88) |
SMTC-X26 |
| SOJ-32, 34 |
.315 (8.00) |
.340 (8.64) |
.840 (21.34) |
.125 (3.18) |
SMTC-X140 |
| SOJ-40, SOM-32 |
.410 (10.41) |
.450 (11.43) |
1.020 (25.91) |
.075(1.91) |
SMTC-X40 |
| SOJ-42 |
.410 (10.41) |
.450 (11.43) |
1.070 (27.18) |
.125 (3.18) |
SMTC-X148 |
| SOMC-14,-16, DB-20 |
.270 (6.86) |
.270 (6.86) |
.440 (11.18) |
.090 (2.29) |
SMTC-X20 |
| SOP-20 |
.270 (6.86) |
.270 (6.86) |
.285 (7.24) |
.100 (2.54) |
SMTC-X138 |
| SOP-28 |
.420 (10.67) |
.420 (10.67) |
.720 (18.29) |
.125 (3.18) |
SMTC-X39 |
| SOP-40 |
.460 (11.68) |
.510 (12.95) |
1.000 (25.4) |
.125 (3.18) |
SMTC-X134* |
| SOP-44 |
.510 (12.95) |
.565 (14.35) |
1.070 (27.18) |
.105 (2.67) |
SMTC-X83 |
| TSOP-28 |
.470 (11.94) |
.505 (12.83) |
.320 (8.13) |
.065 (1.65) |
SMTC-X95 |
| TSOP-40 |
.730 (18.54) |
.760 (19.30) |
.400 (10.16) |
.120 (3.05) |
SMTC-X154 |
| TSOP-56 |
.730 (18.54) |
.760 (19.30) |
.556 (14.12) |
.120 (3.05) |
SMTC-X162 |
| TSOP-32 |
.730 (18.54) |
.760 (19.30) |
.320 (8.13) |
.120 (3.05) |
SMTC-X84** |
600 series x=0 700 series x=1 *=NOT available for 600 series
**=NOT available for 700 series
QUAD TIP CARTRIDGES FOR PLCC
DIMENSIONS IN INCHES (mm) |
 |
| SMT TYPE |
A2 |
A |
B2 |
B |
D |
Part No.
|
| PLCC 18 |
.300 (7.62) |
.330 (8.38) |
.500 (12.70) |
.530 (13.46) |
.150 (3.81) |
SMTC-X11 |
| PLCC 20 |
.360 (9.14) |
.400 (10.16) |
.360 (9.14) |
.400 (10.16) |
.150 (3.81) |
SMTC-X12 |
| PLCC 28 |
.370 (9.40) |
.410 (10.41) |
.570 (14.48) |
.610 (15.49) |
.150 (3.81) |
SMTC-X103 |
| PLCC 32 |
.450 (11.43) |
.500 (12.70) |
.550 (13.97) |
.600 (15.24) |
.150 (3.81) |
SMTC-X16 |
| PLCC 28 |
.455 (11.56) |
.500 (12.70) |
.455 (11.58) |
.500 (12.70) |
.150 (3.81) |
SMTC-X13 |
| PLCC 44 |
.660 (16.76) |
.700 (17.78) |
.660 (16.76) |
.700 (17.78) |
.150 (3.81) |
SMTC-X14 |
| PLCC 68 |
.960 (24.38) |
.995 (25.27) |
.960 (24.38) |
.995 (25.27) |
.220 (5.59) |
SMTC-X18* |
| PLCC 68 dual |
.960 (24.38) |
.995 (25.27) |
.960 (24.38) |
.995 (25.27) |
.220 (5.59) |
SMTC-X28 |
| PLCC 84 dual |
1.165 (29.59) |
1.195(30.35) |
1.165 (29.59) |
1.195 (30.35) |
.220 (5.59) |
SMTC-X29 |
| PLCC 52 |
.760 (19.30) |
.800 (20.32) |
.760 (19.30) |
.800 (20.32) |
.150 (3.81) |
SMTC-X17* |
| PLCC 84 |
1.165 (29.59) |
1.195 (30.35) |
1.165 (29.59) |
1.195 (30.35) |
.220 (5.59) |
SMTC-X19* | 600 series x=0 700 series x=1 for all quads use 700 SERIES tip cartridges
*=NOT available for 600 series
Please note: Dual tip cartridges require two power supply units and two hand-pieces. A Dual Hand-Piece Support (MX-DHS) is also recommended.
QUAD TIP CARTRIDGES FOR QFP
DIMENSIONS IN INCHES (mm) |
|
| SMT TYPE |
A2 |
A |
B |
B2 |
D |
Part No.
|
| SQFP 48 (EIAJ) |
.330 (8.38) |
.330 (8.38) |
.330 (8.38) |
.330 (8.38) |
.100 (2.54) |
SMTC-X121 |
| SQFP 64 (EIAJ) |
.440 (11.18) |
.440 (11.18) |
.440 (11.18) |
.440 (11.18) |
.100 (2.54) |
SMTC-X120 |
| TQFP 44 |
.440 (11.18) |
.480 (12.19) |
.480 (12.19) |
.520 (13.21) |
.110 (2.79) |
SMTC-X159 |
| TQFP 80 |
.485 (12.32) |
.525 (13.34) |
.485 (12.32) |
.525 (13.34) |
.110 (2.79) |
SMTC-X132 |
| QFP 48 |
.550 (13.97) |
.550 (13.97) |
.550 (13.97) |
.550 (13.97) |
.130 (3.30) |
SMTC-X115 |
| VQFP 100 (EIAJ) |
.570 (14.48) |
.610 (15.49) |
.570 (14.48) |
.610 (15.49) |
.110 (2.79) |
SMTC-X118 |
| QFP 128 (3.2 mm fp) |
.620 (15.75) |
.620 (15.75) |
.860 (21.84) |
.860 (21.84) |
.130 (3.30) |
SMTC-X133 |
| QFP 44 |
.635 (16.13) |
.635 (16.13) |
.635 (16.13) |
.635 (16.13) |
.130 (3.30) |
SMTC-X21 |
| QFP 100 (rectangular) |
.650 (16.51) |
.650 (16.51) |
.885 (22.48) |
.885 (22.48) |
.130 (3.30) |
SMTC-X43 |
| QFP 64, 80 |
.675 (17.15) |
.675 (17.15) |
.910 (23.11) |
.910 (23.11) |
.130 (3.30) |
SMTC-X15 |
| QFP 100 |
.805 (20.45) |
.805 (20.45) |
.805 (20.45) |
.805 (20.45) |
.190 (4.83) |
SMTC-X45* |
| QFP 144 |
.805 (20.45) |
.840 (21.34) |
.805 (20.45) |
.840 (21.34) |
.075 (1.91) |
SMTC-X122 |
| QFP 132 |
.985(25.02) |
1.020(25.91) |
.985(25.02) |
1.020 (25.91) |
.125 (3.18) |
SMTC-X86 |
| QFP 100 (square) |
1.040 (26.42) |
1.040 (26.42) |
1.040 (26.42) |
1.040 (26.42) |
.130 (3.30) |
SMTC-X44* |
| QFP 208 DUAL |
1.125 (28.58) |
1.770 (44.96) |
1.125 (28.58) |
1.170 (44.96) |
.114 (2.90) |
SMTC-X81 |
| QFP 120,160 DUAL |
1.165 (29.59) |
1.200 (30.48) |
1.165 (29.59) |
1.200 (30.48) |
.120 (3.05) |
SMTC-X48 |
| PQFP 240 DUAL |
1.290 (32.77) |
1.330 (33.78) |
1.290 (32.77) |
1.330 (33.78) |
.110 (2.79) |
SMTC-X125 |
| QFP 304 DUAL |
1.600 (40.64) |
1.650 (41.91) |
1.650 (41.91) |
1.600 (40.64) |
.200 (5.08) |
SMTC-X158** |
600 series x=0 700 series x=1 for all quads use 700 series tip cartridges
*= Not recommended for 600 series **= not AVAILABLE FOR 600 SERIES
Please Note: Dual tip cartridges require two powersupply units and two hand-pieces. A Dual Hand-Piece Support (MX-DHS) is also recommended.
SOCKET TIP CARTRIDGES (TIP INSIDE SOCKET)
|
|
| Recommended SMD Component |
A |
B |
D |
Recommended Part No. |
Part No. |
| PLCC-20 SOCKET |
.360 (9.14) |
.556 (14.12) |
.115 (2.91) |
SMTC-X144 |
SMTC-1144 |
| PLCC-32 SOCKET |
.456 (11.58) |
.556 (14.12) |
.120 (3.05) |
SMTC-X109 |
SMTC-1109 |
| PLCC-84 SOCKET DUAL |
1.160(40.64) |
1.160(40.64) |
.115(2.91) |
SMTC-X145 |
SMTC-1145 |
600 series x=0 700 series x=1 for all quads use 700 series tip cartridges
Please Note: oDual tip cartridges require two power supply units and two hand-pieces. A Dual Hand-Piece Support (MX-DHS) is also recommended.
|